Pipeline Cathodic Protection Materials
Anodes, monitoring hardware and installation materials for buried pipelines, station piping, casings, grounding grids, AC mitigation and long-term corrosion control projects.
Send drawings or an MTO through WhatsApp or email. No web form is required.
Build a Pipeline CP Materials Enquiry
Start with the approved material take-off (MTO) if you have one. If selection is still open, send the design inputs below and identify which items need review. A product weight alone does not establish the number of anodes needed.
Buried anode assemblies
For prepackaged magnesium anodes, identify the model or required alloy weight, cable size and length, backfill requirements and quantity. Distinguish alloy weight from the complete packaged weight.
Ribbon and interference scope
For zinc ribbon, send the section size, total length, coil requirements and layout. State whether the scope is galvanic CP, grounding or AC mitigation; these functions need the relevant project design review.
Measurement and connections
Link each test station, reference electrode, cable and bonding box to its drawing or MTO line. Include terminal arrangements, cable schedules and installation locations so interfaces can be checked together.
For technical review: share coating condition, soil resistivity, design life, current demand if available, installation constraints and the applicable specification. If a value is unknown, mark it as unknown rather than selecting a model by guesswork.
Review the CP materials package scope ยท Review quality and traceability information
What a Pipeline CP Material Package Contains
A complete enquiry usually covers six groups of materials. The clause references are to ISO 15589-1:2015, the international standard for cathodic protection of on-land pipelines; the project design and specification decide the final quantities.
Galvanic anodes
Magnesium or zinc anodes in backfill. ISO 15589-1 advises against zinc above 50 Ω·m and magnesium above 100 Ω·m soil resistivity unless an engineering evaluation supports it (10.3, 10.4). Anodes are buried 3 m to 5 m from the pipe (10.8).
Prepackaged magnesium anodesImpressed current groundbeds
Deep-well or shallow groundbeds with HSCI, MMO, conductive polymer or other anodes, conductive backfill and vent pipes. Anodes must deliver 125 % of the required current over the design life (9.3).
Groundbed guideTest stations
Stations at intervals not greater than 3 km in rural and 1 km in urban areas, and at isolating joints, casings, bonds, crossings and drainage points (11.2).
Test station guideReference electrodes and coupons
Permanent Cu/CuSO4 electrodes and coupons where IR-free potentials or a.c. corrosion risk have to be assessed, installed close to the pipe (11.4).
Coupons and probesCables and connections
Copper cables without metal armouring, at least 4 mm² to the pipe in galvanic systems and 10 mm² in impressed current systems; aluminothermic charges not above 15 g (8.5.1, 8.5.2).
Cable guideBonds, isolation and AC mitigation
Bond and isolating-joint stations sized for direct, unidirectional or resistive bonds (11.5, 11.7), and zinc ribbon where the design calls for AC mitigation.
Junction and bonding boxesAnode Materials for Pipeline Corrosion Control
Buried pipelines need a cathodic protection design that matches soil resistivity, coating condition, design life, current demand, and installation constraints. CathPro supplies sacrificial anode materials used by pipeline contractors, corrosion engineers, EPC companies, and industrial operators for new construction and maintenance projects.
Magnesium Anodes
Used where a higher driving voltage is required in soil. Typical applications include distribution pipelines, station piping, coated steel structures, and high-resistivity environments.
View magnesium anodesZinc Ribbon Anodes
Used for AC mitigation, grounding mats, pipeline casings, tank rings, and confined installation areas where a continuous ribbon layout is practical.
View zinc ribbon anodesMonitoring and Installation
Reference electrodes, test stations, junction boxes and cable connection materials complete the field measurement and installation interface.
View system componentsRelated Products for Pipeline Projects
Common Pipeline Applications
CathPro anode products are selected for oil and gas pipelines, water transmission lines, buried plant piping, compressor station piping, road and rail crossings, casing protection, and AC interference mitigation near power corridors.
Information Needed for Quotation
For fast technical selection, provide pipeline diameter and length, coating type, soil resistivity, target design life, anode spacing concept, required standard, destination port, and expected delivery schedule.
Pipeline CP Engineering Guides
- Magnesium, zinc or aluminum anodesChoose by electrolyte, resistivity and temperature.
- High-potential vs standard magnesiumWhen the extra driving voltage matters.
- Magnesium anode backfill and installationBackfill, soaking, placement and start-up checks.
- Test station types and wiringLocations, conductors and enclosures.
- Deep-well vs shallow groundbedsGroundbed types, anodes, backfill and venting.
- CP cable sizes and insulationMinimum sections and connection rules.
Buyer Questions
Which anode is commonly used for buried pipeline cathodic protection?
Magnesium sacrificial anodes are commonly selected for buried pipelines in soil, especially where a higher driving voltage is required. Zinc ribbon anodes are often used for AC mitigation, grounding, casings, and confined installation spaces.
What information is needed to size pipeline anodes?
Typical inputs include pipeline coating condition, exposed steel area, soil resistivity, design life, current demand, installation depth, backfill conditions, and applicable project standards.
How often are test stations installed along a pipeline?
ISO 15589-1:2015 (11.2) recommends intervals not greater than 3 km in rural areas and 1 km in urban or industrial areas, plus stations at isolating joints, casings, bonds, impressed current and drainage stations, and at crossings with power lines, railways, rivers and other pipelines.
When are magnesium anodes not suitable for a buried pipeline?
ISO 15589-1:2015 (10.4) advises against magnesium anodes in soil above 100 ohm-m, even with backfill, unless an engineering evaluation or field test confirms the design requirements can be met. For zinc the limit is 50 ohm-m (10.3).
What is the minimum cable size for pipeline CP connections?
ISO 15589-1:2015 (8.5.1) sets 4 mm2 for the cable to the pipeline and 2.5 mm2 to a single anode in galvanic systems, and 10 mm2 to the pipeline in impressed current systems. The design can require more.
Need pipeline anode sizing support?
Send project drawings, soil data, or a material take-off list and we will prepare a matching quotation.