Skip to content
Menu

Subsea & offshore pipeline protection

Offshore & Subsea Pipeline Bracelet Anodes

Half-shell galvanic bracelet anodes cast in Al-Zn-In aluminum alloy or ASTM B418 zinc alloy for submarine pipelines, risers, spool pieces and shore-approach crossings. Matched to coated pipe outside diameter for S-lay, J-lay or reel-lay installation.

Direct engineering desk: sales@cathprocp.com · WhatsApp +86 159 7878 1890

DNV-RP-B401 (May 2021) ISO 15589-2 AMPP SP0387 EN 10204 3.1 inserts
Paired half-shell offshore pipeline bracelet anodes with cast-in clamping lugs
Al-Zn-In route ≥ 2,500 Ah/kg

DNV-RP-B401 Table 8-5 & Section 9 QC (≤ −1.05 V vs Ag/AgCl/seawater).

Cast zinc route ≥ 780 Ah/kg

ASTM B418 Type I or Cd-free Type II for anaerobic seabed mud (< 50 °C).

Half-shell geometry 31.4 – 527.3 kg net

12 standard CP-AB patterns plus custom tooling for any coated pipe OD.

Mechanical & electrical design

Built around pipe coating geometry and lay-barge rollers.

Submarine pipeline bracelets are supplied as matched cylindrical half-shells cast over rolled steel flat-bar frames. Before any tooling is cut, CathPro issues a dimensioned general-arrangement drawing confirming inner bore diameter, half-shell gap, lug detail, electrical bonding jumper tabs and both net and gross mass.

Concrete-coated flush type
Square-ended cylindrical half-shells recessed into concrete weight coating (CWC) cut-outs so the outer anode diameter sits flush with the concrete surface over stinger rollers.
Tapered 3LPE / FBE type
Bevelled-end half-shells mounted directly onto 3LPE, 3LPP or FBE anti-corrosion coating with neoprene or polyurethane compression pads where specified.
Fastening options
Bolted clamping lugs (stud bolts, nuts and lock washers for offshore deck assembly) or weld-together overlap straps where field welding is permitted.
Inner face coating
Coated on the internal cylindrical face toward the pipeline per DNV-RP-B401 §4.10.5 / §5.7.2 to prevent oxide build-up from stressing the clamping hardware.
A. Flush-Mounted in Concrete Weight Coating CWC Bracelet Half-Shell Steel Line Pipe + 3LPE / FBE Flush OD passes smoothly over lay-barge rollers B. Tapered Bracelet on Rigid 3LPE / FBE Pipe Tapered Half-Shell 3LPE / 3LPP / FBE Coated Pipe Chamfered ends + coated inner bore + bolted/welded lugs

Indicative installation profiles. Exact bore diameter, half-shell gap (typically 80–120 mm), taper angle and bonding cable lug geometry are confirmed on the approved CathPro GA drawing.

Standard pattern range (CP-DS-AL-001 Rev. B)

CP-AB series half-shell bracelet anode dimensions

Net mass is Al-Zn-In alloy only; gross mass includes the steel insert assembly. All models can also be cast in ASTM B418 zinc (multiply net alloy mass by ~2.64 for equivalent volume, or specify target zinc net mass for custom mould sizing).

12 standard models listed
Model OD × Width × Thickness × Gap (mm) Net Alloy Mass Gross Mass
CP-AB-5271034 × 516 × 115 × 120527.3 kg562.8 kg
CP-AB-2831034 × 520 × 65 × 120283.0 kg311.9 kg
CP-AB-1911034 × 516 × 40 × 120191.0 kg209.0 kg
CP-AB-190569 × 500 × 76 × 80190.5 kg200.5 kg
CP-AB-138569 × 500 × 57 × 80137.5 kg147.5 kg
CP-AB-88569 × 500 × 38 × 8087.6 kg97.5 kg
CP-AB-80518 × 500 × 38 × 8079.5 kg88.5 kg
CP-AB-64467 × 450 × 38 × 8064.1 kg72.5 kg
CP-AB-50416 × 400 × 38 × 8050.3 kg57.9 kg
CP-AB-48374 × 480 × 34 × 8047.9 kg55.0 kg
CP-AB-41342 × 450 × 34 × 8040.8 kg47.3 kg
CP-AB-31290 × 400 × 35 × 8031.4 kg36.5 kg

Project pipe ODs outside the CP-AB pattern list (from 4-inch flowlines to 48-inch trunklines) are manufactured to custom moulds. Send the pipe schedule or drawing to sales@cathprocp.com for a dimensioned GA drawing with net and gross weights.

Material routes

Al-Zn-In versus cast zinc for subsea pipelines

CathPro casts both alloy systems in-house and quotes strictly to the governing offshore specification.

Parameter Al-Zn-In Bracelet (CP-DS-AL-001 Rev. B) Cast Zinc Bracelet (CP-DS-ZN-001 Rev. A)
Governing chemistryDNV-RP-B401 (May 2021) Table 8-5 (Zn 2.50–5.75%, In 0.015–0.040%, Fe ≤ 0.09%, Cu ≤ 0.003%, Si ≤ 0.12%, Cd ≤ 0.002%)ASTM B418 Type I (UNS Z32120) or cadmium-free Type II (UNS Z13000, Fe ≤ 0.0014%)
QC electrochemical capacity≥ 2,500 Ah/kg (DNV-RP-B401 §5.6.7 / Section 9)≥ 780 Ah/kg (DNV-RP-B401 Annex B / AMPP TM0190)
Closed-circuit potential≤ −1.05 V vs Ag/AgCl/seawater≤ −1.00 V vs Ag/AgCl/seawater
Consumption rate≤ 3.50 kg / A·yr (alloy density 2.70 g/cm³)≤ 11.2 kg / A·yr (alloy density 7.14 g/cm³)
Primary subsea dutyOpen seawater, risers, trunklines and buried offshore lines where minimum weight and thickness matterAnaerobic marine mud, high bacterial activity, high-strength steel hydrogen-embrittlement limits, ambient (< 50 °C) duty

Quality control & documentation

Manufactured and tested within DNV-RP-B401 Section 5 & AMPP SP0387

CathPro HYAL Al-Zn-In alloy holds DNV Type Approval TAS0000505 (material approval valid 19 Sep 2025 – 18 Sep 2030; finished bracelet geometry follows the approved project drawing and ITP).

01

Every heat: Spark-OES chemistry

Certified spectrometer analysis traceable to heat number against DNV-RP-B401 Table 8-5 or ASTM B418 Type I / Type II limits.

02

Every half-shell: Mass, bore & continuity

Individual weighing (±3% on individual gross mass, zero negative deviation on delivered lot total mass), dimensional fit check and insert-to-body electrical resistance check.

03

Destructive sectioning & crack criteria

Transverse sectioning on first-day / PQT production per AMPP SP0387 to verify internal soundness and steel insert bond; surface crack inspection per DNV-RP-B401 §5.6.3 / §8.6.3.

04

Section 9 electrochemical testing & 3.1 MTC

96-hour laboratory QC testing per DNV-RP-B401 Section 9 (or AMPP/NACE TM0190), EN 10204 3.1 steel insert certificates, MPS/PQT/ITP package and optional DNV, BV, ABS, SGS or TÜV witness.

Direct factory quotation

Send your pipeline bracelet schedule for a GA drawing and FOB/CIF quote

Include steel pipe OD, anti-corrosion coating thickness, concrete weight coating thickness (if flush), alloy route (Al-Zn-In or ASTM B418 Type I/II zinc), required net mass per bracelet, quantity, third-party inspection scope and destination port.

Buyer questions

Frequently asked questions

When should submarine pipeline bracelet anodes be cast in Al-Zn-In versus zinc?

Al-Zn-In (≥ 2,500 Ah/kg, −1.05 V vs Ag/AgCl/seawater) delivers over three times the ampere-hours per kilogram of zinc and is standard for weight-sensitive subsea pipelines and risers. Cast zinc to ASTM B418 Type I or cadmium-free Type II (≥ 780 Ah/kg, −1.00 V vs Ag/AgCl/seawater) is chosen where anaerobic seabed mud, bacterial activity or coating overprotection limits apply at temperatures below ~50 °C.

What pipe dimensions are needed to quote half-shell pipeline bracelet anodes?

Provide steel pipe outside diameter, anti-corrosion coating type and thickness (such as 3LPE or FBE), concrete weight coating thickness (if flush-mounted), required net alloy mass per bracelet pair, quantity, alloy standard and clamping method (bolted or welded lugs).

Are bracelet anodes coated on the inner cylindrical face?

Yes. Per DNV-RP-B401 (May 2021) §4.10.5 and §5.7.2, the inner face facing the pipeline coating is coated as standard so corrosion products cannot build up beneath the half-shells and stress the fastening straps.

What inspection and test records are supplied with CathPro bracelet anodes?

Per agreed ITP: spark-OES heat chemistry, net and gross mass records, 100% dimensional and insert continuity checks, EN 10204 3.1 steel insert certificates, AMPP SP0387 destructive sectioning and DNV-RP-B401 Section 9 or AMPP/NACE TM0190 electrochemical reports.