Engineering guide
Buying Aluminum Anodes to DNV-RP-B401: What to Specify and Verify
DNV-RP-B401 is widely cited in offshore and subsea purchase specifications for galvanic anodes. Section 5 covers anode manufacture, Table 8-5 the alloy limits and Section 9 the laboratory quality-control test. This checklist follows the May 2021 edition; clause and table numbers differ in earlier editions, so quote the edition in the purchase order.
Alloy
Composition limits for Al-Zn-In
DNV-RP-B401 Table 8-5 gives the compositional limits that apply unless the owner specifies otherwise.
| Element | Al-based anodes, wt % |
|---|---|
| Zn | 2.5 to 5.75 |
| In | 0.015 to 0.040 |
| Cd | ≤ 0.002 |
| Si | ≤ 0.12 |
| Fe | ≤ 0.09 |
| Cu | ≤ 0.003 |
| Al | remainder |
Source: DNV-RP-B401 (May 2021), Table 8-5. A broader range may be used if the manufacturer demonstrates and assures better performance (3.5.1).
- Chemical analysis is carried out for each heat; for aluminum anodes two samples are taken from every heat above 500 kg, and the spectrometer is checked with reference standards certified by an independent party (DNV-RP-B401 (May 2021), 5.6.1).
- The purchaser may require anode sample material for verification in an independent laboratory (5.6.1).
- All anodes from a testing lot that does not meet the specified composition are rejected (5.6.1).
Purchase document
What the purchase document should state
Section 5.1.2 lists the information the purchaser encloses with a DNV-RP-B401 order.
Information
- Anode material type (aluminum or zinc based) and any special requirement for chemical composition or anode material qualification.
- Tentative dimensions and net anode mass for each anode type, and any special requirement for fastening devices.
Optional requirements
- Utilisation factor; pre-production qualification test (PQT); manufacturing procedure specification (MPS) and inspection and testing plan (ITP), with their documentation schedules.
- Frequency of dimensional, destructive and electrochemical testing during production.
- Handling of non-conformities and concession requests; traceability; retained samples.
- Marking; handling, storage and shipping; final documentation; any further amendments or deviations.
Unless otherwise agreed, electrochemical quality-control testing follows Section 9; the long-term test of Section 10 applies only if the purchaser specifies it (DNV-RP-B401 (May 2021), 5.1.3, 5.1.4).
Qualification
MPS, PQT and ITP
- MPS — prepared for purchase orders of 15,000 kg net alloy or more, or for smaller orders if the purchaser specifies it. It covers core materials, alloy limits, the detailed drawing with gross and net weight and tolerances, insert welding procedures, casting, inspection and testing, coating of surfaces facing the structure (except stand-off anodes), handling, marking, traceability and documentation (DNV-RP-B401 (May 2021), 5.2.1).
- PQT — prepared for orders of 15,000 kg net alloy or more to verify that the MPS achieves the specified properties; unless otherwise agreed, the PQT report is accepted by the purchaser before production starts (5.3.1, 5.3.2, 5.3.6).
- ITP — meets ISO 10005, Sec. 5.10, in table form, listing every quality-control activity with acceptance criteria and inspection, witness and hold points for contractor, purchaser and any third party (5.4.2). The MPS, ITP and daily log are in English unless otherwise agreed (5.4.3).
Production
Inspection during production
- Inserts — materials meet NACE SP0387; inserts for welding to the protected object are traceable to an EN 10204 or ISO 10474 type 3.1 certificate unless otherwise agreed (DNV-RP-B401 (May 2021), 5.5.1).
- No heat treatment of zinc or aluminum-zinc-indium anodes (5.5.8).
- Weight and dimensions — frequency and acceptance criteria per NACE SP0387; positions of protruding inserts are checked on at least 10 % of the anodes of each design (5.6.2).
- Cracks — every anode is inspected to NACE SP0387 with amendments: no cracks penetrating to the inserts, and within sections fully supported by inserts, cracks wider than 2 mm are permitted only if they are at most 100 mm long (5.6.3).
- Destructive testing — at least two anodes of each size, during the PQT or on the first day of production (5.6.5).
- Daily log — all inspection, test and calibration data, updated daily and open to the purchaser (5.6.11).
Electrochemical testing
Quality-control testing to Section 9
When. As a minimum, electrochemical testing is part of the PQT or first-day production test for orders above 15,000 kg of net anode material, and is repeated for each further 15,000 kg (DNV-RP-B401 (May 2021), 5.6.6). Sampling for potential testing by separate mini-castings is done for each heat (9.2.1).
How.
- Specimens 10 mm ± 1 mm in diameter and 50 mm ± 5 mm long, machined from samples (9.2.2).
- Natural seawater with a salinity of at least 30 ‰, or synthetic seawater to ASTM D1141; at least 10 litres per specimen, air-purged, at 20 °C ± 3 °C (9.3.2, 9.3.3).
- Four 24-hour periods at anodic current densities of 1.5, 0.4, 4.0 and 1.5 mA/cm²; 96 hours in total (9.3.7).
- Potentials measured with an Ag/AgCl/saturated KCl electrode and converted to Ag/AgCl/seawater (9.3.8); capacity calculated as ε = 1000·C / Δw (9.3.10).
| Anode material | Electrochemical capacity | Closed-circuit potential at end of 4th period |
|---|---|---|
| Aluminum based | min. 2,500 Ah/kg | ≤ -1.05 V |
| Zinc based | min. 780 Ah/kg | ≤ -1.00 V |
Acceptance criteria: DNV-RP-B401 (May 2021), 5.6.7. Potentials refer to the Ag/AgCl/seawater reference electrode (3.1.5).
If a result fails, re-tests may be made on three specimens from each heat of the testing lot; failure of any specimen rejects all anodes from that heat (9.4.3).
Quality control is not design. DNV-RP-B401 states that these short, accelerated test results are not applicable to CP design (9.1.1 guidance note), and it strongly recommends its default design values even where a manufacturer claims higher performance (3.5.2 guidance note).
Documents
Marking and documentation
- Each anode is marked with the manufacturer’s name or symbol, the anode material (A for aluminum, Z for zinc), heat number and serial number (DNV-RP-B401 (May 2021), 5.7.1).
- All inspection and test results are traceable to a unique anode number or batch, and to the certificates for core and coating materials (5.7.2).
- The manufacturer issues an inspection certificate type 3.1 to EN 10204 or ISO 10474 (5.7.3).
- The purchaser may specify document retention beyond the two-year minimum of NACE SP0387 (5.7.4).
CathPro material approval
CathPro HYAL Al-Zn-In material is covered by DNV Type Approval TAS0000505, issued 19 September 2025 and valid through 18 September 2030, subject to its conditions. It is a material approval: it does not approve every finished-anode design or a complete CP system. See certificates and records for its scope.
Questions
Short answers
- What capacity must Al-Zn-In anodes reach in DNV-RP-B401 quality-control testing?
- At least 2,500 Ah/kg, with a closed-circuit potential of -1.05 V or more negative (Ag/AgCl/seawater) at the end of the fourth test period, tested by the Section 9 procedure (DNV-RP-B401 May 2021, 5.6.7).
- Is the quality-control test capacity the design capacity?
- No. DNV-RP-B401 states that the short-term Section 9 results are not applicable to CP design and recommends its default design values even when a manufacturer claims higher performance.
- When is a pre-production qualification test required?
- Unless otherwise agreed, for purchase orders of 15,000 kg net alloy or more; the purchaser may also specify one for smaller orders (DNV-RP-B401 May 2021, 5.3.2).
Sources
Standards used in this guide
- DNV-RP-B401 (May 2021) Cathodic protection design. Clauses 3.1.5, 3.5.1, 3.5.2; Section 5 (5.1.2 to 5.7.4); Section 9 (9.1 to 9.4); Table 8-5.
- Documents referenced by DNV-RP-B401 and named here without quoting their values: NACE SP0387, ISO 10005, EN 10204, ISO 10474, ASTM D1141.
Values are quoted from the editions listed. Where a project specification, purchase order or CP design states other values, those govern.
Factory supply & quotation
CathPro Al-Zn-In Anode Supply to DNV-RP-B401 (May 2021)
CathPro (Jiaozuo Huayu Magnesium Co., Ltd.) manufactures cast Al-Zn-In stand-off, hull, ballast-tank and submarine pipeline bracelet anodes controlled to DNV-RP-B401 Table 8-5 chemistry and Section 9 quality-control testing (≥ 2,500 Ah/kg, ≤ −1.05 V vs Ag/AgCl/seawater), supported by DNV material approval TAS0000505, EN 10204 3.1 steel insert certificates and agreed MPS/PQT/ITP documentation.
Direct engineering desk (no web form required): sales@cathprocp.com · WhatsApp +86 159 7878 1890